 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| TD3063 Zero-Volt Switching Triac Driver DESCRIPTION The TD3063 consists of a single input LED optically coupled to a zero-volt crossing triac driver. The TD3063 provides high input-to-output isolation and is designed to drive high-powered triacs. Typical uses include interfacing logic level control signals to equipment powered from 110Vac and 220Vac lines. FEATURES APPLICATIONS * * * * * Zero-volt switching 600V blocking voltage High input-to-output isolation (5kV) Low trigger current (5mA MAX) High reliability * * * * * Home appliances Motor/ Drive controls Solid state relays Solenoid / Valve control Temperature Control OPTIONS/SUFFIXES* ABSOLUTE MAXIMUM RATINGS* PARAMETER Storage Temperature Operating Temperature Continuous Input Current Transient Input Current UNIT C C mA mA V mW C MIN -55 -40 TYP MAX 125 85 50 400 6 330 260 * * * * -S -TR -V -H Surface Mount Leadform Option Tape and Reel Option Signifies VDE approval 0.4" Lead Spacing (see mechanical dimension) NOTE: Suffixes listed above are not included in marking on device for part number identification. SCHEMATIC DIAGRAM + Input 1 6 +/- AC Output Reverse Input Control Voltage Total Power Dissipation Soldering Temperature (10s) - Input 2 5 Do Not Use 3 4 -/+ AC Output *The values indicated are absolute stress ratings. Functional operation of the device is not implied at these or any conditions in excess of those defined in electrical characteristics section of this document. Exposure to Absolute Ratings may cause permanent damage to the device and may adversely affect reliability. APPROVALS * * UL and C-UL Approved File # E201932 VDE Approved, Lic # 40011225 (c) 2004 Solid State Optronics * San Jose, CA www.ssousa.com * +1.408.293.4600 Page 1 of 5 TD3063 rev 1.40 (10/25/2004) TD3063 Zero-Volt Switching Triac Driver ELECTRICAL CHARACTERISTICS - 25C PARAMETER INPUT SPECIFICATIONS LED Forward Voltage LED Reverse Voltage Reverse Leakage Current V V A 6 1.2 12 10 1.5 If = 10mA Ir = 10uA Vr = 4V UNIT MIN TYP MAX TEST CONDITIONS OUTPUT SPECIFICATIONS Blocking Voltage Peak Blocking Current On-state Voltage Critical Rate of Rise V nA V V/ s 600 600 60 1.8 500 3 Io = 1uA Vdrm = Rated Itm = 100mA COUPLED SPECIFICATIONS Isolation Voltage Trigger Current Inhibit Voltage Isolation Resistance Holding Current Leakage Current V mA V G A A 50 100 1 If = Rated, Vdrm = Rated, Off State 5 5000 5 20 T = 1 minute Main terminal voltage = 3V If = 5mA DC 500V (c) 2004 Solid State Optronics * San Jose, CA www.ssousa.com * +1.408.293.4600 Page 2 of 5 TD3063 rev 1.40 (10/25/2004) TD3063 Zero-Volt Switching Triac Driver PERFORMANCE DATA Fig.1 On-State Characteristics Fig.2 Inhibit Voltage versus Temperature IDRM1,PEAK BLOCKING CURRENT (nA) Ta,AMBIENT TEMPERATURE (C) Fig.3 Leakage with LED Off versus Temperature ITM,ON-STATE CURRENT (mA) VTM,ON-STATE VOLTAGE (VOLTS) VINH, NORMALIZED Ta,AMBIENT TEMPERATURE (C) Fig.4 IDRM2 ,Leakage in Inhibit State versus Temperature Fig.5 Trigger Current versus Temperature IDRM2 NORMALIZED Ta,AMBIENT TEMPERATURE (C) IFT , NORMALIZED Ta,AMBIENT TEMPERATURE (C) (c) 2004 Solid State Optronics * San Jose, CA www.ssousa.com * +1.408.293.4600 Page 3 of 5 TD3063 rev 1.40 (10/25/2004) TD3063 Zero-Volt Switching Triac Driver MECHANICAL DIMENSIONS 6 PIN DUAL IN-LINE PACKAGE (Through Hole) 6 PIN SURFACE MOUNT DEVICE (SMD) -H Suffix 0.4" Lead Spacing TOLERANCE :+ 0.25mm Unit in (mm) (c) 2004 Solid State Optronics * San Jose, CA www.ssousa.com * +1.408.293.4600 Page 4 of 5 TD3063 rev 1.40 (10/25/2004) TD3063 Zero-Volt Switching Triac Driver DISCLAIMER Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this document. SSO reserves the right to make changes to product description, specifications at any time without further notice. SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither circuit patent licenses nor indemnity are expressed or implied. Except as specified in SSO's Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we make no other warranty, expressed or implied, including merchantability and fitness for particular use. LIFE SUPPORT POLICY SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or death. Users of SSO devices in life support applications assume all risks of such use and agree to indemnify SSO against any and all damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when used properly in accordance with instructions for use can be reasonably expected to result in significant injury to the user, or (d) a critical component in any component of a life support device or system whose failure can be reasonably expected to cause failure of the life support device or system, or to affect its safety or effectiveness. (c) 2004 Solid State Optronics * San Jose, CA www.ssousa.com * +1.408.293.4600 Page 5 of 5 TD3063 rev 1.40 (10/25/2004) |
Price & Availability of TD3063
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |